Ghost 2 Immobiliser Reviews
The ghost 2 immobiliser is an innovative anti-theft system that utilizes modern technology to ward off car theft. This discreet device is unnoticeable by thieves and only turns on the engine after a PIN or app is entered.
It's weatherproof and connects to the CAN data network of your vehicle. It also comes with the service/valet mode that allows you to temporarily start your car when it's in the garage for cleaning or servicing.
Easy to install
The Ghost immobiliser guards your vehicle from theft of keys or hacking, as well as cloning. It utilizes an exclusive PIN code system that is incorporated into your car's ECU, making it difficult for thieves to identify or alter. In contrast to traditional immobilisers, it doesn't require specific keys or sensors. It is completely hidden from view with no LED indications or signals to signal its presence. It is also cheaper than replacing an ECU or installing the new key fob. Additionally, it can lower your monthly insurance premiums.
When installing a Ghost 2 immobiliser, be sure to follow the instructions of the manufacturer carefully. This will ensure that the device operates correctly and effectively. After the installation is complete, test the system by entering the PIN code and starting the engine. Regular testing will enable you to identify any problems in the early stages.
Make sure you check the position of the CAN H and L wires prior to beginning the installation. They are vital for powering the immobiliser, therefore it is crucial to connect them correctly. It is also a good idea to label the wires to make it easier to locate them during the installation process. Once you've identified the locations of these wires and connected them to a continuous 12V power source and a grounding point. Use the fuse tap to safeguard the connections against damage or short-circuits.
After connecting the wires, neaten the wiring with cable ties to guard against interference. It is also recommended to cover the wires with insulation tape or heat shrink tubing. This will protect them from electrical shorts and extend the lifespan of the device. Once the wiring is secured, it's a good idea to test the Ghost 2 immobiliser.
In situations where you have to hand over your vehicle, for instance for servicing or valet parking for valet parking, the Ghost 2 immobiliser has a service mode that temporarily disables the PIN code sequence. Press the brake pedal and hold down the accelerator for a number of times equal to the first digit in the emergency code. The system will go into service mode. This can be confirmed by flashing five times the indicator signal.
Easy to change PIN codes
Ghost 2 immobilisers are an excellent way to safeguard your vehicle from theft. It is installed discreetly within the vehicle, and is accessible only by a special code. The device communicates with the vehicle ECU via its data bus and does not rely on radio frequency signals, as aftermarket alarm systems or traditional Thatcham immobilisers do. This makes it harder for thieves to detect the sound of an immobiliser relay or add new keys. The control unit is hidden in the vehicle's wiring or dashboard, and can't be physically tampered to reset the system.
The ghost 2 immobiliser connects to your vehicle's CAN Data network. G28 Car Keys uses buttons on the door panels, the steering wheel and the center console, to create a customized sequence of up to twenty button presses, which must be entered to start the engine - just as a PIN. This unique system is reprogrammable and doesn't require cutting wires when installing. You can even set your vehicle in Valet or Service mode to allow it to be started for a short time when you give it to a mechanic to work.
The application can also be used to block your PIN number if you've lost your keys, or change it. This feature is particularly useful in the event that you have offered your vehicle to someone else to be used as a valet or service because it prevents them from starting your car and driving it away without permission. It is also inaccessible to professional thieves as it does not use any radio frequencies or circuit cuts.
Another excellent feature of the ghost 2 immobiliser is its capability to prevent relay thefts. Relay theft is among the most common methods of car theft. Criminals gain access to your car's diagnostic ports, then modify the signal sent by the car's ECU to fool it into thinking that the car's key is valid and present. The traditional immobiliser can be bypassed in this manner, however with the ghost 2 immobiliser the signal is blocked by the immobiliser prior to it gets to the ECU.
Easy to use app
Ghost 2 is a revolutionary immobiliser that shields your vehicle from key-cloning, hacking and key theft. It works by connecting to your vehicle's CAN data network and demanding that you enter a PIN code before it will start the engine. It also stops thieves from using signal spoofing and device spoofing, which are both common tactics employed to steal vehicles.
The system is simple to use and functions as a standard auto alarm. The installation of the system allows you to create an individual 20-digit PIN code that you must enter before you start the vehicle. This will stop the vehicle from being taken even if the keys are removed. You can disable the system with an app on your smartphone.
The ghost is completely silent and does emit radio frequency signals. It is a weatherproof, discrete device that can be installed anywhere inside your vehicle. It can be concealed under the dash, steering wheel, or door panels. It communicates with your ECU via the CAN data circuit, and is not affected by diagnostic tools that thieves use to find security systems. It is also not affected by jamming devices that spoof codes.
It is a covert installation that doesn't require any cutting of wires or modifications to the vehicle it can be used as an anti-theft system for all vehicles. The technology has been proven effective, and it complies with TASSA Standards. The ghost is a fantastic solution for classic, sports and prestige cars. It can be used to safeguard vehicles that are let out on websites like Turo.
The Autowatch Ghost 2 represents the next generation of car immobilisers. The system is completely inaccessible to thieves, and prevents the vehicle from starting without your PIN, or unless they are authorized by the app. It doesn't emit radio frequencies or other signals scanners could detect. Installation is quick and easy. The app is simple to navigate and offers a user-friendly interface which makes it easy to install and use. It also includes a GPS tracker that can assist police locate the vehicle and then recover it.
Simple to reset
It is possible to protect your vehicle from theft using a ghost 2 immobiliser. It connects to your vehicle's ECU to create a security barrier that thieves cannot break through without a valid PIN. It's also TASSA verified which means it's recognized by insurance companies. It's a great tool to prevent car theft and will save you money in the long run.
Unlike traditional alarm/immobilisers that require circuit cutting, the Ghost system is connected directly to the vehicles CAN data network and operates with the existing buttons on the dashboard and steering wheel. You can design a unique PIN that is up to 20 presses in length. This PIN needs to be entered before your engine can begin as it would be the PIN you use on your credit card. The Ghost system is undetectable to thieves, and there are no indicators that signal its presence making it the most effective aftermarket CAN bus immobiliser available on the market currently.
Another advantage of the Ghost system is that it doesn't make use of radio frequency signals, which means it isn't scanned or intercepted by thieves. This helps to prevent the cloning of keys and relay attacks as well as the more common method of hacking a car's CAN bus system by scanning for signals from its alarm/immobiliser. The Ghost system is designed so that it can be hidden within your vehicle. There aren't any lights, or other indicators to show its presence.
The system also has the option of a Transport Mode that disables the Ghost system that is helpful in situations in which you have to temporarily disable it, such as during transportation or maintenance. However this mode isn't as efficient as Service Mode, as it does not disable the system if your vehicle goes over 31 mph for more than 15 minutes.
To reset your ghost 2 immobiliser you'll need the emergency code, which is available from your installer. The code is typically hidden beneath the scratch-off portion of the card that came with the installation. This emergency code should be kept secure and stored in a secure place, such as a wallet at home.